Published by on March 26, 2020
Categories: Sex

This instruction manual provides information specific to the AIRANGER XPL PLUS (Ten Point Level) monitor. When references are made to other Milltronics. AiRanger XPL Plus. * Program range is defined as the empty distance to the face of the transducer (P) plus any range extension (P). **EMC performance. AiRanger XPL Plus. Ten-Point Ultrasonic Level Measurement System. Part 1. General. Scope. A. This section describes the requirements for an ultrasonic.

Author: Dakinos Mezijin
Country: Antigua & Barbuda
Language: English (Spanish)
Genre: Photos
Published (Last): 2 February 2005
Pages: 384
PDF File Size: 10.30 Mb
ePub File Size: 10.6 Mb
ISBN: 535-1-70437-881-4
Downloads: 96212
Price: Free* [*Free Regsitration Required]
Uploader: Shajas

Application Assistance The preceding examples describe only a few ways in which the XPL Plus can be applied to plsu measurement requirements. Should a stable measurement still not be attainable, contact Siemens Milltronics or your local distributor. Increase Measurement Response as required to stabilize the Reading, or install a stilling well contact Siemens Milltronics or your local distributor.

May not post to United States – Read item description or contact seller for postage options. Not all components or their maximum quantity may be required. This value is automatically altered by Material P The Profile Pointer may be moved to a number of airangfr on the Echo Profile, to gain specific information dependent upon the Profile Pointer Parameter used. This item may be a floor model or an item that has been returned to the seller after a period of use.


Loosen the 6 enclosure lid captivated screws and swing the lid open. Page 71 Enter the width of false echoes in ms to be removed from the long shot Echo Profile. Add to Watch list Watching Watch list is full.

Milltronics AiRanger XPL Plus Instruction Manual

Don’t have an account? This item will be sent through the Global Shipping Programme and includes international tracking. Operation is similar to Space Measurement operation except that measurements are referenced to the transducer face. If the Reading is currently displayed in feet, to display in yards, enter 3. Otherwise, when “fastback” iaranger selected, the Failsafe Level Advance is restricted, however the advance to the new material level when a valid measurement is made is immediate.

Enter a negative value if Empty is below sea level. Page 4 Measurement Parameters P to P Page 35 when process control equipment is used avoid entering a value so short as to cause nuisance activation.

Siemens SITRANS LU10 Ten-Point Ultrasonic Level Transmitter (Milltronics AiRanger XPL Plus)

Use these features to record and save a total of up to 10 Echo profiles, initiated manually Por automatically P et al. If a Tripper Car is used to fill each section of the bunker, see Example 4 as well. If more than one mA airanver is allocated to the same Point Number, the value of the lowest mA Output Number is displayed.

Insulate tape cable shields at all shield junctions to prevent ground loops. When the reported level reaches By pressing ‘print’ button you will print only current page.


Transducer sound beam is free from obstruction. Removed from a plhs distribution depot for upgrading purposes. Before activating this feature, connect terminal block contacts 42 to 45 and 43 to Seller assumes all responsibility for this listing.

P Empty Enter “65” for transducer face to Empty equals 65 ft. Page If the material monitored is a liquid, check for splashing in the vessel.

To enter the program mode This is the value displayed when is pressed in the RUN mode. Page Extend Near Blanking P to a distance from the transducer face to just beyond the distance represented by the Reading.

For additional information, see the Global Shipping Programme terms and conditions – opens in a new window or tab This amount includes applicable customs duties, taxes, brokerage and other fees.

Instruction Manual March Page 93 P Empty Enter “65” for transducer face to Empty equals 65 ft. AO required Adjustable range and over-range limits. To move the Profile Pointer to a specific point, enter the desired value.

Please check the appropriate transducer manual for details.