ASTM D1200 PDF

Published by on May 13, 2020
Categories: Sex

ASTM D – Designation: D – 10 Standard Test Method for Viscosity by Ford Viscosity. ASTM D Standard Test Method for Viscosity by Ford Viscosity Cup. mm (˝) Orifice diameter; 25 – cSt Viscosity range; 40 – sec. Flow times. Viscometer Flow Cup, ASTM D, Ford No 3 · Viscometer Flow Cup.

Author: Malajora Toramar
Country: Singapore
Language: English (Spanish)
Genre: Video
Published (Last): 12 January 2018
Pages: 392
PDF File Size: 1.38 Mb
ePub File Size: 2.14 Mb
ISBN: 442-4-23329-967-5
Downloads: 56227
Price: Free* [*Free Regsitration Required]
Uploader: Kajas

A number in parentheses indicates the year of last reapproval.

Summary of Test Method 4. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

Under no conditions should metal cleaning tools be brought into satm with the instrument. Calibration Procedure for Ford Cups X1.

A percent correction can be applied to the seconds? Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Temperature of Testing 8.

Fill the cup with the prepared specimen. If the ratio of shear stress to shear rate is not constant, the liquid is nonNewtonian. A small change in diameter of the ori? The frequency of this calibration check depends upon the amount of use and the care that the individual cup receives.

  ANNIE DILLARD THE STUNT PILOT PDF

Originally approved in Precision and Bias Box 16, State College, Pa. NOTE 2— It is impossible to predict the effect of temperature change on each material with which the apparatus may be used. Care of Cup If the material is non-Newtonian, that is, shear-thinning or thixotropic, Test Method D should be used.

Make the viscosity determination at the end of the min period.

ASTM D1200

Temperature drift during the test should be kept to a minimum and should not exceed Last previous edition approved in as D — 94 Bring this cup and the liquid viscosity standard to a constant temperature as close as possible to ASTM D 2. Allow to stand undisturbed for 10 min while adjusting further to the desired temperature.

Determinations should be made at a temperature above the dew point of the atmosphere surrounding the apparatus. Keep the temperature drift to within Oils available from other sources, having known kinematic viscosities, may also be used.

This standard has been approved for use by agencies of asstm Department of Defense. In addition, temperature measuring devices such as non-mercury liquid-in-glass thermometers, thermocouples, or platinum resistance thermometers that provide equivalent or better accuracy and precision, that aztm the temperature range for thermometer 17C and 17F, may be used.

  2SK2500 DATASHEET PDF

Permission rights to photocopy the standard may also be secured from the ASTM website www. Pull the stopper away and simultaneously start the timing device.

ASTM D – 10() Standard Test Method for Viscosity by Ford Viscosity Cup

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. NOTE 1—If the ori? Particular care dd1200 be exercised in cleaning the ori? If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

For particular oils applicable for use with the Ford Cups refer to Table X1. Determine the time of efflux to the nearest 0.

ASTM D | Hanatek Instruments

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Measure the time until the? The preferred method is to over? The values given in parentheses are for information only. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Current edition approved July 1,