ASTM D3654 PDF

Published by on March 21, 2020
Categories: Politics

ASTM D – Designation: D /D M – 06 Standard Test Methods for Shear Adhesion of. ASTM D/DM: Standard Test Methods for Shear Adhesion of Pressure- Sensitive Tapes. A summary of ASTM standards relating to pressure sensitive tape is attached. The shear test procedures are also harmonized: ASTM D and PSTC.

Author: Fenrijin Zolozuru
Country: Bangladesh
Language: English (Spanish)
Genre: Education
Published (Last): 25 February 2005
Pages: 178
PDF File Size: 3.87 Mb
ePub File Size: 17.93 Mb
ISBN: 927-9-84908-339-5
Downloads: 3178
Price: Free* [*Free Regsitration Required]
Uploader: Matilar

ASTM D3654/D3654M – 06(2011)

Repeat for a total of three washes with this solvent. Record the d36654 elapse in which the tape specimen has completely separated from the test panel. Take care in astn choice of samples and when comparing results between fiberboard surfaces which may not be exactly the same.

In order to offer you the best service, Algomtl uses cookies. Examples of averages and with-in-roll standard deviations including test error are as follows: The adequate solution for the transport of your fresh products or frozen food or of your organic and Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

Add to Alert PDF.

asttm One company reports that, with care, the between laboratory standard deviation and the residual including within roll standard deviation may be higher or lower than reported here, depending on the tape type and manufacturer.

  DALEMARK QUARTET PDF

Equipment goods Search in a category: Procedure A measures the ability of a pressure-sensitive tape to adhere to a standard astj panel under constant stress. Your comments will receive careful consideration at a meeting of the responsible technical committee,1 which you may attend.

China Supplier ASTM D3654 Polymide Tape Lasting Adhesive Test Meter

Other grades may be used, provided it is? ASTM D The test plate with adhesive specimen is vertically hanged on the stand and its bottom is attached with a standard weight.

Combining values from the two systems will result in non-conformance with the standard. The edges shall be separated by 12 6 0.

Roll down the test area twice in each lengthwise direction with the rubber-covered steel roller described in 5. The components of the variance for the following factors were estimated: Asym mass of the roller shall be 6 45 g [4. You may delete a document from your Alert Profile at any time.

For Procedures A and H, substitute steel panel instead of? ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Measure any slippage that has occurred to the nearest 1 mm [1?

The 24 mm [1 in. The surfaces of similar fiberboards may exhibit considerable variation between mills, between batches from one mill, and within batches. It is the responsibility xstm the user of this standard to establish appropriate safety and asfm practices and determine the applicability of regulatory limitations prior to use.

  INNATIST THEORY PDF

Adhesion is asmt bond produced between a pressure-sensitive tape adhesive and a surface for Procedures A, B, C, D, and H; and, This may or may not relate to the ability of the tape to adhere to other surfaces.

This may be used to compare 3d654 shear adhesion of a tape to a particular fiberboard surface or to compare the shear adhesion of a tape to a variety of fiberboard surfaces.

These censored data may have a time to termination rather than a time to failure.

ASTM D | Rycobel

Owen Zhang86 The assessment may be within a roll of tape, between rolls or production lots. Subscription pricing is determined by: It is common to test at least?

Width of specimen for Procedures E, F, and G if other than 12 mm [0. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. The precision of tests conducted on nonstandard surfaces may be different than that described wstm Section